Building Automation & Controls for Manufacturing Facilities

USA Controls serves manufacturing plants and industrial facilities across Southern Wisconsin with HVAC controls, shift-based automation, access control, and video surveillance — built around production schedules, not generic office templates.

Controls That Match How a Plant Actually Runs

Manufacturing facilities have building systems demands that commercial integrators routinely underestimate. Large variable occupancy between shifts. Process exhaust and makeup air requirements tied to production activity. Security perimeters that need to align with shift changes and production floor access rules. Office, production floor, and support spaces that run on completely different schedules and have different environmental requirements. Off-the-shelf schedules and generic occupancy modes don't reflect how a plant operates. We program building automation and access control systems around your shifts, production schedules, and facility layout — so the building supports the operation rather than fighting it. Everything is self-performed and built on open BACnet.

Industrial HVAC and makeup air unit in a manufacturing facility mechanical room

HVAC Controls for Production & Support Spaces

Manufacturing facilities typically have multiple distinct building environments — production floors with high heat loads and process exhaust requirements, offices with standard comfort conditioning, and support spaces like locker rooms, break rooms, and storage areas with different occupancy patterns. We program separate control sequences for each, coordinated through a single Delta Controls head-end.

  • Production floor HVAC with makeup air and process exhaust coordination
  • Office and support area conditioning on independent schedules
  • High-bay heating sequencing and destratification fan control
  • Evaporative cooler and spot cooling integration where applicable
  • Open BACnet — system is yours, serviceable by any qualified integrator

Shift-Based Scheduling & Occupancy Automation

A manufacturing facility running two or three shifts has occupancy patterns that a simple 9-to-5 schedule can't capture. Setbacks during shift changes, different ventilation requirements at peak production versus low-capacity runs, equipment that needs to pre-condition spaces before a shift starts — these are the kinds of control sequences we build at the controller level, tailored to how your plant actually operates.

  • Multi-shift HVAC scheduling with pre-conditioning before shift start
  • Automatic setbacks between production runs and during shift changes
  • Weekend and holiday schedules programmed in advance
  • Lighting tied to shift occupancy — zones on when needed, off when not
  • Schedule overrides for unplanned production runs or maintenance windows
Manufacturing workers during a shift change on a production floor
Access control card reader at a manufacturing plant entrance

Access Control for Production Floors & Restricted Areas

Manufacturing facilities need access control that aligns with how the plant is staffed — shift-based door scheduling, restricted access to tooling rooms, chemical storage, server rooms, and executive areas, and credential management that can handle contractor and visitor access alongside permanent staff. We program at the controller level so the rules match your operation, not a factory preset.

  • Shift-based door scheduling — access permissions change with shift transitions
  • Production floor, tooling, chemical, and server room zoning
  • Contractor and visitor credential management
  • Loading dock and perimeter gate access control
  • Complete audit trail reporting for all access events

Video Surveillance for Industrial Facilities

Manufacturing surveillance needs are different from a typical office building — large floor areas, loading docks, exterior yards, perimeter fencing, and after-hours coverage when the facility is at reduced staffing. We design camera coverage for the specific layout and security requirements of your facility, with hardware rated for industrial environments where temperature, dust, or moisture may be a factor.

  • Production floor, loading dock, and perimeter gate coverage
  • Industrial-rated cameras for dust, moisture, and temperature environments
  • After-hours and low-light coverage for reduced-staffing periods
  • NVR storage sized for your retention requirements
  • Remote viewing for management and security personnel from any device
Industrial security camera mounted on a manufacturing plant production floor
Niagara building automation supervisor dashboard integrating multiple systems in an industrial facility

Niagara Integration for Mixed Equipment Environments

Older manufacturing facilities often have building systems from multiple eras and manufacturers — HVAC equipment with legacy controls, lighting systems on separate platforms, and no unified visibility across the building. Tridium Niagara is the industry-standard open supervisor for bringing mixed-protocol systems onto a single head-end. We deploy Niagara to pull BACnet, Modbus, LonWorks, and other protocol devices into one interface, giving facilities managers a complete view of building operations without replacing existing equipment.

  • Integration of BACnet, Modbus, LonWorks, and other protocol devices
  • Single head-end for all building systems regardless of manufacturer
  • Unified alarm and event reporting across all integrated systems
  • Reuse of existing field devices where viable — reduce replacement cost
  • Hosted Niagara option — web access without on-premise servers

Ready to Build Controls That Match Your Operation?

Whether you need a new installation, a retrofit off legacy equipment, or Niagara integration to unify existing systems, we serve manufacturing facilities across Southern Wisconsin. Tell us about your plant and we'll put together a plan.