HVAC Controls for Commercial & Institutional Buildings

USA Controls designs, installs, programs, and services intelligent HVAC control systems across Southern Wisconsin — on open BACnet architecture you own and can service with any qualified provider.

Smarter HVAC. Lower Energy. Total Control.

Most HVAC problems aren't mechanical — they're a controls problem. Zones that won't balance, schedules nobody has touched in years, equipment that runs when nobody is in the building. We specialize in the controls layer that sits between your mechanical equipment and the results you actually want: comfortable spaces, predictable energy costs, and systems that do what you designed them to do. From new Delta Controls BAS installations to retrofits of aging proprietary platforms, our team handles the engineering, wiring, programming, and commissioning under one roof.

Delta Controls BACnet touchscreen panel in a commercial mechanical room

New HVAC Controls & Building Automation Systems

We are an authorized Delta Controls partner. Every system we install runs on open BACnet architecture — meaning you are not locked to us or any single vendor for service or expansion. Our engineers design the control sequence, program the controllers, run the wire, and commission the finished system. The same team that engineered it brought it online.

  • VAV and zone control systems
  • Air handler unit (AHU) sequencing and scheduling
  • Chiller and boiler plant sequencing and staging
  • Rooftop unit (RTU) control and scheduling
  • Demand-controlled ventilation (DCV) with CO₂ sensing
  • Custom controller-level programming — if you can describe the behavior, we can build it

HVAC Controls Retrofits & Platform Migrations

Legacy controls platforms reach end-of-life — no firmware updates, no replacement parts, and a single vendor who knows you have no options. We migrate aging and proprietary HVAC controls onto open BACnet, so you own your building systems again and any qualified integrator can service them going forward.

  • Migration off proprietary and dead-end HVAC controls platforms
  • Reuse of existing field devices — sensors, actuators, dampers — where viable to reduce demo cost
  • Open BACnet controllers replacing legacy logic, panel for panel
  • Sequence-of-operations rewritten and improved during migration
  • Full commissioning and verification after cutover
  • As-built documentation delivered so the system is serviceable by any qualified party
Technician replacing an aging HVAC controls panel inside a commercial building
Commercial rooftop HVAC units on a flat roof

Rooftop Unit & Packaged Equipment Controls

RTUs are often the most neglected part of a building's HVAC controls strategy — running on factory defaults with no integration into the larger BAS. We connect rooftop and packaged equipment into your Delta Controls system so scheduling, setpoints, and occupancy modes are managed in one place alongside your air handlers and zone equipment.

  • BACnet-enabled RTU controls replacing or supplementing factory boards
  • Occupied and unoccupied setback scheduling tied to BAS occupancy logic
  • Demand-limit strategies to reduce peak electrical load
  • Alarm and fault monitoring integrated with your building head-end
  • Multi-unit sequencing for buildings with several RTUs serving common zones

Controls Commissioning & Functional Testing

A building automation system is only as good as its commissioning. Equipment installed but never properly verified drifts away from design intent — sometimes from day one. We commission every system we install and offer standalone commissioning services for systems installed by others that aren't performing as designed.

  • Point-by-point I/O verification — every sensor, actuator, and control point confirmed
  • Sequence-of-operations testing against design documentation
  • Setpoint and schedule review and correction
  • Alarm threshold configuration and testing
  • Deficiency log and corrective action tracking to close-out
  • Commissioning report delivered at project completion
Engineer with tablet commissioning a building automation system in a mechanical room
Building energy and HVAC monitoring dashboard on a computer screen

Remote Monitoring & Energy Optimization

Most facilities managers find out an HVAC system stopped doing its job when a tenant calls or an energy bill spikes. We give you visibility before that happens. Our team monitors your building systems offsite and can access your Delta Controls head-end remotely to respond to alarms, adjust setpoints, and troubleshoot — often before you know there is a problem.

  • Remote alarm monitoring and response
  • Setpoint and schedule adjustments handled offsite — no truck roll needed for small changes
  • Energy trend analysis — identify equipment running out of hours or fighting other systems
  • Hosted enteliWEB or Niagara supervisor — web access to your building from any device, no on-premise servers
  • Support portal at support.usacontrols.us for existing customers

Preventive Maintenance for HVAC Controls

HVAC controls drift. Sensors go out of calibration. Schedules get changed by someone years ago and never changed back. A preventive maintenance agreement keeps your system running the way it was designed to run — catching problems on a scheduled visit instead of after a failure. We maintain what we install, and we take on existing systems too.

  • Scheduled PM visits — quarterly, semi-annual, or annual depending on your facility
  • Setpoint, schedule, and alarm threshold review
  • Sensor calibration verification and correction
  • Firmware and software updates
  • On-call service response for issues between visits
  • Priority scheduling for agreement customers
  • Service history and documentation maintained on file
HVAC technician performing preventive maintenance on a controls panel in a mechanical room

Ready to Get Your HVAC Controls Right?

Whether you need a new system, a retrofit off a dead platform, or a service partner who already knows Delta Controls — we cover Southern Wisconsin from Milwaukee to Madison. Tell us what you're working with and we'll tell you what makes sense.