Lighting Control for Commercial & Institutional Facilities
USA Controls designs, installs, and programs lighting control systems across Southern Wisconsin — integrated directly with your building automation system so lighting, HVAC, and occupancy work together as one.
Lighting That Works With Your Building, Not Against It
Most commercial facilities lose energy to lighting every day; lights running in empty rooms, spaces lit at full output when daylight is doing the work, schedules nobody has updated in years. Lighting control fixes that. But the biggest gains come when lighting isn't managed as its own isolated system. When lighting is integrated with your building automation system, a single occupancy mode can set the temperature, adjust the lighting zones, and lock the right doors all at once. We program and install that kind of integration, and because we self-perform the installation, the team that designed the logic is the same one that ran the wire.
Scheduled Lighting by Zone, Floor & Space Type
Time-based lighting schedules are the foundation of any controlled lighting strategy. We program zone-level schedules that match how your building is actually used — office areas, common spaces, corridors, parking structures, and exterior lighting all running on independent schedules that can be adjusted in one place without touching each zone separately.
- Zone-level scheduling — individual control per area, floor, or space type
- Occupied, unoccupied, and after-hours lighting levels
- Holiday and exception schedules
- Exterior and parking lighting tied to sunrise/sunset or time
- Override capability for after-hours staff or special events
- Schedule changes managed from a single BAS interface
Occupancy-Based Lighting Control
Schedules tell lights when to turn on. Occupancy sensors tell them when to turn off. Combining the two eliminates the energy waste that schedules alone can't catch — conference rooms left lit after meetings, private offices running at full output all afternoon, corridors lit for nobody. We integrate occupancy sensing directly with your BAS so lighting responds to actual presence, not assumptions about it.
- Occupancy and vacancy sensor selection and placement
- Per-zone timeout and delay configuration
- BAS-integrated occupancy logic — lighting and HVAC respond together
- Manual override without disrupting the control sequence
- Occupancy data available for energy reporting and audits
Daylight Harvesting
In perimeter offices, open areas near windows, and atrium spaces, electric lighting often runs at full output while daylight is already doing the work. Daylight harvesting uses photosensors to continuously measure ambient light levels and dim or raise electric lighting to maintain a consistent target — so you're only adding what the sun isn't providing. For facilities with significant window exposure, the energy savings can be substantial.
- Photosensor selection and placement for accurate daylight measurement
- Continuous dimming to a consistent illuminance target
- Closed-loop control — adjusts automatically as conditions change throughout the day
- Compatible with dimmable LED and fluorescent fixtures
- Coordinated with occupancy and schedule logic in the BAS
Integration with Building Automation Systems
Running lighting as a standalone system means every schedule change has to be made twice — once for lighting and once for HVAC. Integrating lighting into your Delta Controls building automation system eliminates that. One occupancy mode change propagates across lighting zones, HVAC setpoints, and access schedules simultaneously. We program that integration at the controller level, so the coordination is built into the logic, not patched together after the fact.
- Single scheduling interface for lighting, HVAC, and access control
- Occupancy modes that coordinate lighting and mechanical setbacks together
- Unified alarm and event logging across all systems
- BACnet-native integration — no middleware or third-party bridges
- Energy data from lighting available alongside HVAC trend data for reporting
Energy Monitoring & Reporting
Lighting is typically one of the largest controllable energy loads in a commercial building. Knowing how much your lighting system is consuming — by zone, floor, or building — is the first step toward reducing it. When lighting is managed through your BAS, energy trend data is logged alongside HVAC and mechanical data, giving facilities managers a complete picture of building energy use rather than fragmented reports from isolated systems.
- Lighting energy trend logging through the BAS
- Zone and floor-level consumption visibility
- Identification of zones running outside scheduled hours
- Data available for utility benchmarking and sustainability reporting
- Remote access to trend data via hosted enteliWEB or Niagara platform
Ongoing Service & Preventive Maintenance
Lighting control systems drift over time — schedules get manually overridden and never restored, sensors go out of calibration, and firmware falls behind. A service agreement keeps your system performing as designed after the install is done. We maintain the lighting control systems we install, and we take on existing systems too.
- Scheduled preventive maintenance visits
- Schedule and setpoint review — confirm zones are running as intended
- Sensor calibration verification and correction
- Firmware and software updates
- On-call service response for issues between scheduled visits
- Priority scheduling for agreement customers
- Service history and documentation maintained on file
Ready to Take Control of Your Lighting?
Whether you need scheduling, occupancy sensing, daylight harvesting, or full BAS integration, we can scope and install it across your facility in Southern Wisconsin. Tell us what you're working with and we'll tell you what makes sense.